Mapit – NTRIP Client App Manual

Real-Time Positioning with Mapit – NTRIP Client

Please note: Mapit NTRIP Client is using RTKLIB library and you need to have a supported GNSS receiver to be able to use it with this application. Before buying subscription please do ensure that your receiver is working well with the app (7 days FREE Trial is available to test the application).

RTKLIB compatible receivers can be found here:, however other devices may be also supported but you need to determine this yourself.

The manual below is based on RTKLIB Manual and Mapit NTRIP Client is an Android port of the original library.

The application inputs raw observation data of GPS/GNSS receivers and execute navigation processing in real-time.
By setting the positioning mode to Kinematic and configuring the rover and the base station receiver data inputs, RTK-GPS/GNSS is enabled
with OTF (on-the-fly) integer ambiguity resolution.

The following figure shows the data flow in the app. You have to set up Input Streams, Output
Streams (optional) and Log Streams (optional) for real-time positioning.

Mapit NTRIP Client – Streams


Input Streams and data format

For real-time positioning with Mapit – NTRIP Client, you have to input the raw observation data and satellite ephemerides from the GPS/GNSS receivers. To set the input stream, click “Input streams” on the app menu.

Input Streams

Check and set the stream type of Rover, Base-station or Correction in the dialog. If you set the “Positioning Mode”  option  “Single” in the “Processing Options”, the input streams for  “Base-station”  and  “Correction”  are not required. The stream types can be selected from the following options:

1. Bluetooth

2. USB

3. TCP Client (Connect to a TCP server and input data via the TCP connection) – If you select “TCP Client”  as the stream type, you can then set the options of “TCP server address”  and the  “Port” number with the  “TCP Client Options” dialog.

4. NTRIP Client (Connect to a NTRIP caster and input data via the NTRIP) – If you select “NTRIP Client” as the stream type, you can set the options of “NTRIP Caster Host” address, “Port”  number,  “Mount-point”  of NTRIP caster,  “User-ID”  and  “Password”  with the  “NTRIP Client Options” dialog. If you keep the “Port” field blank, the default port number (2101) of NTRIP is used. Note that “User-ID” cannot contain “:”.

5. File (Input data from a log file).

You have to select the stream data format from the following options with the pull down menu under “Format“. You shall configure your GPS/GNSS receivers to output at least GPS/GNSS observation data and navigation data (ephemerides).
For detailed operation for the receiver settings, refer the appropriate manuals for the GPS/GNSS receivers or contact Manufacturers.

– RTCM2 (RTCM 2.3)
– RTCM3 (RTCM 3.0, 3.1 (with amendment 1-5) and 3.2
– NovAtel OEM3 : NovAtel OEM3 (Millennium) binary format
– NovAtel OEM6 : NovAtel OEM4/V/6 and OEMStar binary format
– u-blox    : u-blox LEA-4T, 5T,  6T, 8T etc. binary format
– Septentrio
– Tersus
– Furuno LPY-10000
– Hemisphere    : Hemisphere Crescent/Eclipse binary format
– SkyTraq    : SkyTraq S1315F binary format
– GW10    : Furuno GW-10-II/III binary format
– Javad    : JAVAD GRIL/GREIS binary format
– NVS BINR    : NVS NV08C BINR format
– BINEX    : BINEX format (only supports big-endian, forward, regular CRC)
– SP3    : SP3 precise ephemeris (only for Correction)
– Trimble RT17

Mapit NTRIP Client - Formats

Mapit NTRIP Client – Formats

In case of using a NRTK (network RTK) service, which requires NMEA GPGGA messages to select reference station or to setup the (virtual reference station) position, select  the message content with the pull down menu at  “Transmit NMEA GPGGA to Base Station”.  If you select “Latitude/Longitude”  to send a fixed position, fill in the latitude and longitude of the position for NMEA GPGGA messages in degree (minus means south or west).

Similar to the ROVER input stream you need to set the BASE one – this is usually done via NTRIP (Network Transport of RTCM via Internet Protocol) caster.

After the BASE and ROVER is set up, you can start the RTK Service and start processing the data to get RTK solution which then can be used in Mapit application.


RTK processing

Push   “Start Service”  switch on the navigation drawer.

Start/Stop RTK Service

Start/Stop RTK Service

The status of each streams are shown on the upper right indicators. From the left, they show the stream/processing status of Input Rover, Input Base Station, Input Correction, the positioning process, Output Solution 1 – (this one is not available in Mapit NTRIP Client as it has been reserved for internal use), Output Solution 2, Log Rover, Log Base Station and LogCorrection.

RTK Processing Status

RTK Processing Status

Gray represents not used, Orange means waiting for the connection, Deep‐green means connected or running, Light‐green means data active (input, output or processing) and Red means a communication error occurs. To stop the positioning process in Mapit NTRIP Client –  push  “Stop Service”  switch.

After the input observation data and ephemerides are completed and valid, RTKLIB computes the positioning solution and display it in the solution display area with the solution status (FIX, FLOAT, DGPS, SBAS, SINGLE or PPP), E/N/U or X/Y/Z components of the standard deviation, Age (age of differential), Ratio (ratio factor of ambiguity validation) and # of Sat (number of valid satellites). To switch the format in the solution display, push   button  Settings button in upper right corner. You
can switch the solution to Lat/Lon/Height (degree/minute/second), Lat/Lon/Height (degree),X/Y/Z‐ECEF (m), E/N/U‐Baseline (m), Pitch/Yaw/Length‐Baseline (deg, m), alternatively.

RTK Solution

RTK Solution

The Height element in Mapit NTRIP Client is always ellipsoidal – Geoid height correction can be then set in Mapit GIS if required.



If you can't explain it simply, you don't understand it well enough. Albert Einstein

Leave a Reply